Machine embroidery on t-shirts without puckering
A t-shirt is made of jersey, a knit that stretches in every direction. Embroidery doesn’t stretch at all. If the knit shifts during thousands of stitches, it stays locked out of shape once the hoop comes off: that is the rippling around the design. The whole secret is keeping the knit still from the first stitch to the last.
Why t-shirts pucker
Three causes, nearly every time:
- The knit was stretched in the hoop. It springs back when you unhoop, the embroidery doesn’t, and the fabric ripples around it.
- The stabilizer doesn’t hold enough. Tearaway comes off, leaving nothing under the stitches to hold a knit that moves with every wash.
- The design is too dense. A large solid fill pulls the knit towards it and turns the t-shirt into cardboard.
The right stabilizer
On knits, use cutaway: it stays under the embroidery and supports it for good. On a pale or thin t-shirt, choose a light one (no-show nylon mesh) so it doesn’t show through. After stitching, trim it about 5 mm (¼ in) from the design, rounding the corners, and never cut into the shirt.
The full fabric-by-fabric chart is here: “Stabilizer for machine embroidery: which one for which fabric?”.
Hooping without stretching
- Wash the t-shirt first, without fabric softener: new cotton often shrinks in its first wash, and the embroidery won’t shrink with it.
- Mark the centre of the design with a disappearing marker or a pin, with the shirt lying flat.
- Slide the hoop in from the hem, stabilizer underneath, and close it without pulling the knit. The fabric should be flat and smooth, not drum-tight: the one exception to the rule.
- Or don’t hoop it at all: hoop sticky stabilizer on its own, peel the paper and press the t-shirt onto it (floating). The knit is never pulled.
- Clip the rest of the shirt out of the way (back, sleeves) so the machine doesn’t stitch through it.
Problems and fixes
What you see on the t-shirt, and what to change:
| What you see | Why | The fix |
|---|---|---|
| Ripples around the design | The knit was stretched in the hoop | Hoop flat without pulling, or float the shirt on sticky stabilizer |
| The design puckers after washing | Tearaway: nothing left holding the knit | Cutaway, which stays under the stitches |
| Tiny holes along the stitches | A sharp needle cuts the knit | A 75/11 ballpoint needle |
| A design as stiff as cardboard | Too many stitches: big fill, high density | Light density, a more open design |
| The stabilizer shows through | Stabilizer too heavy or too dark | A light cutaway, skin-tone or white |
| Hoop burn on the fabric | A tight hoop on a delicate knit | A little steam, without pressing the iron down |
And in the studio?
In Stitch settings, choose the Light density for a t-shirt and leave Underlay (holds the fabric) ticked: it anchors the knit before the top stitches. For a name, the studio warns you if the letters are too small for the chosen font. Then On an item shows the design on a T-shirt, Left chest or centred, life-size and with your machine’s hoop. A towel calls for different habits: “Machine embroidery on towels”.
Common questions
Can I embroider a t-shirt with tearaway stabilizer?
It holds while you stitch, but not in the wash: with no support, the knit shifts under the stitches and puckers. On a t-shirt, use cutaway.
The cutaway stabilizer feels scratchy inside: what can I do?
Trim it short and rounded, then cover the back of the embroidery with a very soft iron-on backing made for the job. On a baby bodysuit it is almost essential.
Try the studio
Create your design and the studio exports the file in your machine’s format.
Try the studioRead next
Stabilizer for machine embroidery: which one for which fabric?
Tearaway, cutaway, water-soluble… The right stabilizer for t-shirts, sweatshirts, towels and denim.
Machine embroidery on towels
Terry loops swallow stitches. With a water-soluble topping and the right font, the name stays crisp.
Machine embroidery hoop sizes: which hoop for which design?
4×4, 5×7… Find your hoop’s real embroidery field, and what to do when a design won’t fit.