Lesbrodeuses

Machine embroidery on towels

4 min read · Published on 16 November 2026

A terry towel is covered in tiny loops of thread. Stitch on it without care and they poke up between and over the stitches: the name looks thin, patchy, sometimes unreadable. The fix comes down to one word: topping. The loops need flattening while the machine stitches.

In shortLay a water-soluble topping on the towel, use tearaway underneath (or sticky stabilizer if the towel is too thick to hoop), and pick a bold, large enough font. The topping washes away and the name sits on top of the loops.

Why stitches disappear

On smooth fabric every stitch stays where the needle put it. On terry, the loops spring back up between the stitches and partly cover them. Fine details go first: the thin strokes of a script font, the inside of a and e, the dots on the i.

A water-soluble topping laid on top flattens the loops while stitching and keeps the stitches on the surface. Once the embroidery is done, it tears away around the design and the rest dissolves in water.

What you need

  • On top: a clear water-soluble topping, cut slightly larger than the design.
  • Underneath: tearaway stabilizer, or sticky stabilizer for a thick towel.
  • Thread: 40 weight polyester, which handles hot washes and bleach: “Machine embroidery thread: polyester or rayon?”.
  • Needle: a new embroidery needle, 75/11 for a thin towel, larger (90/14) for very thick terry.

Towel by towel:

TowelUnderneathOn topTip
Hand towel or bath towelTearawayWater-soluble toppingAbove the woven band
Bath sheet, thick beach towelSticky, hooped on its ownWater-soluble toppingDon’t force the hoop
Hooded baby towel, washcloth, terry bibSticky, hooped on its ownWater-soluble toppingSmall pieces: pin outside the design
Velour towel (one sheared side)TearawayWater-soluble toppingStitch on either side
Waffle weave, tea towelTearawayNoneFlat fabric: no topping needed

Step by step

  1. Wash the towel first: new terry often shrinks a little.
  2. Choose the spot: on a bath towel, a name usually goes above the woven band, centred, so it shows when the towel is folded.
  3. Hoop the towel and stabilizer together. If it is too thick to close the hoop, hoop sticky stabilizer on its own, peel the paper and press the towel onto it.
  4. Lay the topping over the area. A few pins outside the design, or a dab of water at a corner, hold it in place.
  5. Stitch, then tear the topping away around the design. Bits caught between letters disappear in the first wash, or with a little warm water.

A name that stays readable

  • A bold font: rounded or block letters rather than a fine script. Thick strokes stay above the loops.
  • Big enough: the studio knows the minimum height for each font (8 to 15 mm depending on the font) and warns you below it. On terry, go well above that minimum: on a bath towel, letters 2 to 3 cm (about 1 in) tall read from across the room.
  • Not too light: keep the Normal density so the thread covers the terry well. A towel is not a t-shirt: “Machine embroidery on t-shirts without puckering”.

And in the studio?

Type the name with the Text tool, then open On an item: choose Bath towel, its colour, and the Above the band position. Everything is life-size, with your machine’s hoop, so you see straight away whether the name is big enough and fits the hoop (“Machine embroidery hoop sizes: which hoop for which design?”).

Common questions

Can I embroider a towel without topping?

With a very solid design and big bold letters you can sometimes get away with it. For an ordinary name, topping makes all the difference, and it costs next to nothing.

My towel is too thick for the hoop: what now?

Don’t force the hoop: it would mark the terry or pop open. Hoop sticky stabilizer on its own, press the towel onto it and hold it with a few pins outside the design.

Try the studio

Create your design and the studio exports the file in your machine’s format.

Try the studio